NET R3 Reference

Command List

Ethernet networking

Ethernet network settings may be modified and then applied using the net.apply command. Setting a hostname permits mDNS access at hostname.local.

• net.hostname – [string] Name for mDNS lookup; access at udp://hostname.local.
• net.mode – [string] Choose dhcp, static, auto.
• net.address – [string] Device IP address, like 10.0.1.100.
• net.gateway – [string] Gateway IP address, like 10.0.1.1.
• net.netmask – [string] Netmask, like 255.255.255.0.
• net.apply – Commits changes to network settings.

Device configuration memory

• dev.conf.autosave – [i16] Automatically save configuration specified number of seconds after changes; -1 disables. Maximum one million writes.
• dev.conf.save – Save configuration. Configuration is used on next power cycle.
• dev.conf.load – Load configuration from last saved version.

Device information

• dev.name – Short name of device.
• dev.model – Short name of device.
• dev.desc – Description of device.
• dev.serial – Serial number assigned to device.
• dev.revision – [u16] Hardware revision number.
• dev.version_major – [u16] Software version, major rev number in major.minor format.
• dev.version_minor – [u16] Software version, minor rev number in major.minor format.
• dev.lock – Attempts to secure advisory lock. No effect in device; useful for multi-client access control.
• dev.unlock – Unlock the advisory lock. No effective in device; useful for multi-client access control.
• dev.systime – [u64] Time elapsed since boot counted by microcontroller.
• dev.loglevel – [u8] Set max level of log messages sent by device.
• dev.session – [u32] Random number set at power on.
• dev.firmware.upload – Used to upload firmware into RAM. See the tio-firmware-upgrade in tio-tools.
• dev.firmware.upgrade – Used to commit firmware to flash. See the tio-firmware-upgrade in tio-tools.
• dev.firmware.serial – Serial number/identifier of firmware.

Data stream introspection

Devices have multiple data sources, sampled on specific timebases, which can be selected for streaming.

• data.rate – Specify primary source data rate (Hz)
• data.timebase.list – Number of timebases availbale on device; internal clock, external clock, etc.
• data.timebase.info – Request with timebase ID, reply with timebase metadata.
• data.timebase.send – Request with timebase ID, sends timebase metadata.
• data.source.list – Number of data sources available on device.
• data.source.info – Request with data source ID, reply with source metadata.
• data.source.send – Request with data source ID, sends soure metadata as source update.
• data.stream.list – Number of data streams. Most systems have only one data stream.
• data.stream.info – Request with data stream ID, reply with stream metadata.
• data.stream.send – Request with data stream ID, sends data stream metadata as stream update.
• data.stream.columns – Number of active columns in stream.
• data.list – List active streams. Request with ID to enumerate stream names.
• data.send_all – Iteratively sends metadata on all timebases, sources, and streams.
• data.atomic – Preface a set of atomic data stream changes.
• data.apply – Apply data stream changes atomically.

Command introspection

• rpc.list – No argument: List number of RPCs. Pass [u16] ID number: returns name of RPC.
• rpc.info – [u16] Return RPC metadata, 16 bits.
• rpc.listinfo – Same as rpc.list, but prepends rpc.info metadata.
• rpc.id – Return 16 bit ID number for named RPC.
• rpc.name – [u16] Return RPC name string for 16 bit ID number.

Communications port configuration

• dev.port.boot_mode – [u8] Startup mode of this port 1=text, 0=binary.
• dev.port.text – Change mode of this port to text.
• dev.port.binary – Change mode of this port to binary.
• dev.port.count – [u32] Number of control ports.